SPS/IPC/DRIVES

27. - 29.11.2018

Nuremberg

Hall 4, booth 351

Electric Automation - Systems & Components

Place:Nuremberg
Date:27. to 29. November 2018
Booth:Hall 4, booth 351

 

Get your free ticket here.

 

Booth staff

27.11.28.11.29.11.
Mr. Niedermannxxx
Mr. Schmitzxxx
Mr. Langsdorfxxx
Mr. Thielxxx
Mr. Ravarixxx
Mr. Gracaxxx
Mr. Kinselxxx
Mr. Frößingerxxx
Mr. Leixxxx
Mr. Häusleinxxx
Mr. Schmattlochxx
Ms. Pabstxx
Mr. Gräbxxx
Mr. Schybollxxx
Mr. Möllx
Mr. Muhmxxx

 

Key aspects:

ISOMETER® iso685…

LINETRAXX® RCMS150

LINETRAXX® PEM353

LINETRAXX® PEM353

The digital universal measuring device PEM353 is used to record and display measured quantities of an electricity supply network, and make them available via the communication interface.
The range of measurements extends from voltages and currents to power and energy meters to measured quantities of the voltage quality, such as THD and the individual harmonics up to the 31st order.
The PEM353 is suitable for use in 2-, 3- and 4-wire systems and in their respective versions as TN, TT and IT systems. This allows monitoring single and polyphase systems. With its standardised dimensions of 96 x 96 mm, the device is intended for front panel mounting.

ISOSCAN® EDS440

ISOSCAN® EDS440

The insulation fault locators ISOSCAN® EDS440 are used in connection with the ISOMETER® iso685-D-P or the locating current injector PGH to locate insulation faults in unearthed power supply systems (IT systems).
They detect locating current signals generated by the insulation monitoring device iso685-D-P or IRDH575 or the locating current injector PGH and evaluate them correspondingly. Up to 12 measuring current transformers can be connected to an EDS440. In total, up to 21 insulation fault locators can be connected via an RS-485 interface (BS bus protocol) and thereby up to 252 outgoing circuits can be monitored.

ISOMETER® iso685…

ISOMETER® iso685…

The ISOMETER® is an insulation monitoring devices in accordance with IEC 61557-8 for IT systems. The devices are universally applicable in AC, 3(N)AC, AC/DC and DC systems. AC systems may include extensive DC-supplied loads (such as rectifiers, inverters, variablespeed drives).

Device variants

iso685-D: This device variant ISOMETER® iso685-D features a high-resolution graphic LC display and operating controls for direct operation of the device functions. It cannot be combined with an FP200.
iso685-S: This device variant ISOMETER® iso685-S features neither a display nor operating controls. It can only be used in combination with the FP200 and it is operated via this front panel.
Option "W": The ISOMETER®s with and without integrated display are available with option „W“ for extreme climatic and mechanical conditions (ISOMETER® iso685W-D and iso685W-S).

LINETRAXX® RCMS150

LINETRAXX® RCMS150

The 6-channel residual current monitor RCMS150 is intended for measurement of AC and DC fault currents in earthed systems, which can emerge from insulation faults on loads with six-pulse rectifiers or one-way rectifiers with smoothing. The device can measure residual currents up to IΔ = 500 mA in a frequency range of DC 0…2 kHz. Two separately adjustable response values allow a distinction to be made between prewarning and alarm.
The device features an RS-485 interface which can be used to transfer measured values and alarm values. Setting parameters is also possible via this interface.

eMobility

Electrical safety from the charging socket to the electric vehicle

Electrical safety both in the electric vehicle itself and in the charging infrastructure is of key importance in the use of electric vehicles (EV). As in all areas of everyday life, protecting people from the hazards caused by electrical current is top priority here too. more >>

MRCD

MRCD residual current device in accordance with DIN EN 60947-2

When the pre-alarm threshold is exceeded, a potential-free contact switches. Pre-alarm offers system operators numerous benefits, such as:

  • Early information on the level of insulation prior to shutdown
  • Prevention of unscheduled system shutdowns
  • Higher operational and electrical system safety
When the set response value is exceeded the RCM's alarm relays switch and trigger the undervoltage release of the circuit breaker.
This device combination provides a protective device in accordance with DIN EN 60947-2 Annex M that fulfillls the following protection objectives, while taking into account the maximum disconnection times:
  • Protection of persons
  • Protection against fire
  • System protection

LINETRAXX® PEM353

ISOSCAN® EDS440

Back
SPS/IPC/DRIVES